None 7270015-IP62HO Manuel d'instructions télécharger pdf

Fig 3

ASSEMBLY OF THE TREE

1. Locate the bottom section of the tree which is identified

by a label on the outer branches marked “A” (Fig 5).

2. Remove the protective plastic cap by twisting and pulling

it from the end of the pole, (that is pinched to a point), and

place the end into the tree stand. Be sure the pointed end

of the pole extends to the bottom end of the stand.

3. Now tighten the eyebolts evenly on the tree stand; being

careful not to over-tighten (Fig 3).

ASSEMBLY INSTRUCTIONS

(We recommend wearing proper clothing in order to prevent

scratches that may occur during the assembly process.)

Carefully unpack the contents from the tree’s carton (Fig 1);

including the contents of the poly-bag that is adhered to the

interior flap of the tree’s carton.

Contained in the poly-bag are LED replacement bulbs and a

remote control which operates your tree’s 3 function lighting

capability.

Your tree should include the following components:

A folding metal tree stand with (3) eyebolts.

An ON/OFF push button foot pedal with cord and plug (Fig 6);

which is pre-attached at the lowest section of your tree (Fig 5).

7.5’ trees will have (3) tree sections; (“A”, “B” and “C”; as shown

in Fig 5).

NOTE: If you have purchased a 9' tree this carton will contain

sections “A”, “B” and the tree's stand. A second carton will be

provided containing sections “C”, “D”and “E”.

Model No. 7270014-IP62HO

7270015-IP62HO

ASSEMBLY OF THE TREE STAND

1. Remove the tree stand from the plastic bag, loosen the eye

bolt and open the tree stand to form an “X”.

2. Align the holes for the insertion of the remaining (2)

eyebolts.

3. Insert each eyebolt and begin threading in a clockwise

direction for a couple of rotations only; leaving enough

room for the tree’s pole from section “A” to be inserted into

the assembled stand (Fig 2).

4. Place the tree stand in its desired location; as once the tree is

fully assembled, it may be too difficult to move and relocate.

4. Carefully cut the nylon strapping bounding the branches

upright.

CAUTION: Be extremely careful not to cut any of the exposed

light set wires.

5. Now gently guide the branches downward into place.

6. Beneath the canopy of section “A”, contains an push button

foot pedal with cord and plug (Fig 6).

Remove the twist-tie binding the cord together and insert

the plug into a working electrical outlet.

3. If the top of the tree or another individual lettered section does

not illuminate, remove each section and then reinsert as

instructed, to ensure the electrical connection is made.

NOTE: The tree’s top is designed specifically for a secure and

firm connection point. Downward force will be needed to

ensure that the electrical connection occurs.

4. Always inspect your tree for any burned out LED bulbs.

Although the tree will continue to remain lit even if a bulb

burns out, is loose or is missing; any burned out LED bulbs

should be replaced promptly to ensure the performance and

life expectancy of your tree.

5. If lighting is out of sequence after replacing an LED, remove

and re-insert the LED making sure to align the husk tabs as

illustrated in the safety instruction sheets. This is a specialty

bulb. Do not replace with a standard LED or Incandescent bulb.

NOTE: DO NOT USE A DIMMER SWITCH, INSTALL ANY

ADDITIONAL LIGHTING OR ORNAMENTION THAT IS

POWERED THROUGH THE LIGHT BULB SOCKETS. DOING

THIS MAY RESULT IN DAMAGE TO THE LIGHTING SYSTEM

OR MAY CAUSE PERSONAL INJURY; THEREFORE VOIDING

THE LIMITED WARRANTY PROVIDED WITH THIS PRODUCT.

1. Gently remove the plug from its electrical outlet, and carefully bind

the cord which contains the push button foot pedal and plug.

2. Beginning with the tree’s top section; lift each section straight

up from the section below, and continue working downward.

NOTE: You may have to slightly wiggle each section as you lift

each section upward.

3. To remove the bottom and final section; loosen the eyebolts by

turning in a counter-clockwise direction and lift section “A”

from the support collar of the tree stand.

4. Gently fold the branches of each section upward, towards the

center, and position in the storage container.

NOTE: With the exception of the tree’s “top” section; by holding

each section upside down; the branches will collapse

downward, due to the hinging, aiding in the packing of each

section into the storage container.

5. Fully unthread the eyebolts from the tree’s stand and fold

together; placing in the storage container.

6. It is recommended to always store the tree in a cool, dry

location protected from excessive exposure to heat or sunlight.

NOTE: Store your remote control in a SAFE & DRY location and

remove the battery from remote control before storage.

DISASSEMBLY & STORAGE OF THE TREE

NOTE: ALTHOUGH THE LED LIGHT STRINGS ON THE TREE ARE

RATED FOR INDOOR OR OUTDOOR USE; THE COMBINATION

OF THE TREE WITH THE LED LIGHTS IS RECOMMENDED FOR

INDOOR USE ONLY.

Fig 2

9. Once section “B” is fully inserted downward into section “A”;

both section “A” and section “B” will now be lit.

10. Again, carefully cut the nylon strapping bounding the

branches upright; being extremely careful not to cut any of

the exposed light set wires.

11. Now gently guide the branches of section “B” downward

into place.

12. Depending on the height of the tree you have purchased,

you will continue to build your tree upwards, section by

section, following the above steps until the tree is

completely assembled. Each section of the tree is labeled in

alphabetical order beginning from the bottom to the top.

7. Locate the next section of the tree which is identified by a

label on the outer branches marked “B” (Fig 5).

8. Remove the protective plastic cap by twisting and pulling it

from the end of the pole on section “B”; insert that end onto

the top of the pole of section “A” (Fig 4).

Fig 4

EZ-POWER™ TECHNOLOGY

NOTE: Your tree has been designed with EZ-Power™

technology; allowing for each of the tree’s remaining

sections to light up automatically, upon a firm insertion of

each lettered section (Fig 5).

CCT15

Fig 1

Fig 6

Connection 2

Connection 1

Foot Pedal

Fig 5

• Color Change White to Multi

(Color fades between White

and Multi)

• Steady White

(Color remains white)

• Steady Multi

(Color remains multi)

REMOTE CONTROL OPERATION

Contained in the poly-bag; which is adhered to the interior flap

of the tree’s carton, is your remote control that operates your

tree’s 3 lighting functions.

Before operation; a standard 9 volt type battery (6F22, 6LR61 or

23F6-220) must be installed into the remote control; by simply

removing the slide plate located on the back of the remote

control.

The remote controls the

following 3 functions as well as

the ON/OFF operation. To change

the functions, simply press the

“Function ” or “Function ” to

cycle through each function.

NOTE: If the tree is powered off by

the use of the push button foot

pedal, remote control or by

unplugging it from the electrical

outlet; when powered back on the

tree will default to color change.

TROUBLESHOOTING

1. If the tree does not illuminate press the function button on

your remote control. If failure to light persists the battery may

need to be replaced. Insert a standard 9 volt type battery (6F22,

6LR61 or 23F6-220); aligning the appropriate ( +/- ) markings

accordingly.

If the tree fails to light due to a damaged or defective remote

control; please resort to manual push button foot pedal

operation until a new remote control can be provided through

our customer service center.

2. If failure to light persists, press the push button foot pedal; as it

may be in the “Off” mode.

Made in China

Printed in China

This is not a toy, for decorative use only.

DISTRIBUTED BY HOME DEPOT U.S.A., INC. 2455

This product was pre-tested before shipment and date

coded. In keeping with the National Electric Code, this

product is intended for seasonal (90 days max.) installation

and use. The 3 year limited warranty covers repair or

replacement of this product if it fails to light. This product

is covered under warranty only if it is used as intended for

3 holiday seasons (90 days max. per season). If product

fails to light, call Home Depot customer service toll-free at

1-877-527-0313. This warranty is void if the product is

misused or damaged in any way.

3 YEAR LIMITED WARRANTY

15”

2015 Home Depot US

7.5ft / 9ft Natural Balsam - Tree Instruction Sheet (English)

Date: 3/12/15

11.5”

1 2

2015 Home Depot US 1
Date: 3/12/15 1

Résumé du contenu

Page 1 - Date: 3/12/15

Fig 3ASSEMBLY OF THE TREE1. Locate the bottom section of the tree which is identified by a label on the outer branches marked “A” (Fig 5).2. Remove th

Page 2

Fig 3INSTRUCCIONES PARA EL ENSAMBLAJE(Recomendamos llevar ropa apropiada para evitar rasguños que pueden ocurrir durante el proceso de ensamblaje.)Des

Commentaires sur ces manuels

Pas de commentaire

None 7270015-IP62HO Manuel d'instructions

Naviguer en ligne ou télécharger Manuel d'instructions pour Non None 7270015-IP62HO. none 7270015-IP62HO Instructions / Assembly Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Non None 7270015-IP62HO